Интерфейсный модуль Juniper MIC3-100G-DWDM

release

·         Junos OS Release 15.1F5 and 15.1F6, Junos OS Release 17.1R1 and later

For information about which MPCs support this MIC, see MIC/MPC Compatibility. For information about which MICs are supported on MX Series routers, see MICs Supported by MX Series Routers.

Description

·         One 100-Gigabit DWDM OTN port

·         Power requirements (including transceiver) at different temperatures:

·         55° C: 1.90 A @ 48 V (91 W)

·         25° C: 1.73 A @ 48 V (83 W)

·         Weight: 2.3 lb (1.04 kg)

·         Model number: MIC3-100G-DWDM

·         Name in the CLI: 1X100GE DWDM CFP2-ACO

Hardware features

·         Dual-wide MIC that installs into two MIC slots

·         Supports CFP2 analog coherent optics (CFP2-ACO)

·         Transparent transport of a 100-Gigabit Ethernet signal with OTU4V framing

·         ITU-standard OTN performance monitoring and alarm management

·         Dual-polarization quadrature phase shift keying (DP-QPSK) modulation

·         Supports three types of forward error correction (FEC):

·         Soft-decision FEC (SD-FEC)

·         High-gain FEC (HG-FEC)

·         G.709 FEC (GFEC)

·         100 channels on C-band ITU grid with 50-GHz spacing

·         Latency:

·         SD-FEC: 14 µs (TX + RX)

·         HG-FEC: 22 µs (TX + RX)

·         GFEC: 6 µs (TX + RX)

·         Interoperable with the CFP-100GBASE-ZR transceiver supported on the 100-Gigabit Ethernet MIC with CFP (MIC3-3D-1X100GE-CFP) on MX Series routers and the 100-Gigabit Ethernet PIC with CFP (P1-PTX-2-100GE-CFP) on PTX Series routers.

·         Interoperable with the 100-Gigabit DWDM OTN PIC with CFP2 (PTX-5-100G-WDM) on PTX Series routers when the 100-Gigabit DWDM OTN MIC is configured to use SD-FEC or GFEC.

Note: The 1-port 100-Gigabit DWDM OTN MIC is not directly interoperable with the 2-port 100-Gigabit DWDM OTN PIC (P1-PTX-2-100G-WDM), but they can both operate over the same DWDM line system.

Software features

Note: For information about configuring the MIC, see Configuring OTN Interfaces on MIC3-100G-DWDM MIC. For information about upgrading the firmware on the PIC, see Upgrading Firmware on the 100-Gigabit DWDM OTN MIC (MIC3-100G-DWDM).

·         Compliant with ITU G.709 and G.798

·         Provides a transport interface and state model (GR-1093)

·         Performance monitoring features such as alarms, threshold-crossing alarms, OTU/ODU error seconds and FEC and bit error rate (BER) statistics

·         SNMP management of the MIC based on RFC 3591, Managed Objects for the Optical Interface Type, including the following:

·         Set functionality

·         Black Link MIB

·         IFOTN MIB

·         Optics MIB

·         FRU MIB

·         Pre-FEC BER monitoring provides interrupt-driven, BER-based detection of link signal degradation for MPLS fast reroute.

·         User-configurable optics options:

·         Transmit (TX) laser enable and disable

·         TX output power

·         Wavelength

·         Receive (RX) LOS warning or alarm thresholds

·         Threshold crossing alarms (TCAs)

User-configurable card options:

·         FEC mode (SD-FEC, HG-FEC, or GFEC)

·         TCAs