Маршрутизатор Cisco C1113-8PLTEEAWE

Model

WAN

Wi-Fi

LAN switch

Integrated USB

3.0 console

Pluggable

GE

GE/SFP

combo

ADSL2/VDSL2+

LTE Advanced (CAT6)

802.11ac

GE

PoE or PoE+

C1113-8PLTEEAWE

NA

1

1 G.FAST (Annex A)

1 EMEAR &

North America

2X2 MIMO

8

4

2

Yes

NA

Feature

Specification

Memory (default and maximum)

DRAM: 4 GB

Only C1111X-8P model have 8GB DRAM

Flash: 4 GB

Only C1111X-8P model have 8GB Flash

Console

Micro USB console (USB 3.0).

Mini-USB port (reserved)

Micro-USB port to support remote LTE diagnostics and monitoring tools (Qualcomm CAIT and Spirent UDM) (USB 3.0).

WLAN interfaces

Multiuser Multiple-Input Multiple-Output (MU-MIMO) allows transmission of data to multiple 802.11ac Wave 2– capable clients simultaneously to improve the client experience. Prior to MU-MIMO, 802.11n and 802.11ac Wave 1 access points could transmit data to only one client at a time, typically referred to as Single-User MIMO (SU-MIMO).

802.11ac Wave 2 with 2x2:2 MIMO technology uses two spatial streams when operating in SU-MIMO or MU-MIMO mode, offering 867-Mbps rates for more capacity and reliability than competing access points.

Flexible deployment through the Mobility Express solution is ideal for small to medium-sized deployments. Easy setup allows the 1100 Series (similar to 1815i) to be deployed on networks without a physical controller.

Maximum clients

Maximum number of associated wireless clients: 200 per Wi-Fi radio; in total 400 clients per access point.

Authentication and security

AES for Wi-Fi Protected Access 2 (WPA2).

802.1X, RADIUS AAA.

802.11r and 802.11i.

802.11ac

2x2 SU-MIMO/MU-MIMO with two spatial streams.

Maximal Ratio Combining (MRC).

20-, 40-, and 80-MHz channels.

PHY data rates up to 866.7 Mbps (80 MHz on 5 GHz).

Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Rx).

802.11 Dynamic Frequency Selection (DFS).

Cyclic Shift Diversity (CSD) support.

Software

Cisco Unified Wireless Network Software with AireOS Wireless Controllers Release 8.5 (8.8 for 1101 and 1109 Models) MR1 or later.

DSL interfaces

C1116 & C1117

Dying gasp.

ITU G.993.2 (VDSL2) and supported profiles: 8a, 8b, 8c, 8d, 12a, 12b, and 17a.

VDSL2 Vectoring.

ADSL Annex A and Annex B ITU G. 992.1 (ADSL), G.992.3 (ADSL2), and G.992.5 (ADSL2+).

ADSL Annex M G.992.3 (ADSL2) and G.992.5 (ADSL2+).

C1112 & C1113

G.FAST (spectrum up to 106MHz) Annex A, Annex B, Annex M and compatible with ADSL2/2+ and VDSL2.

ITU G.993.2 (VDSL2) and supported profiles: 8a, 8b, 8c, 8d, 12a, 12b, 17a, and 35b.

ITU G.9700/9701/997.2 G.FAST and supported profiles: 106a, and 106b.

C1118

G.SHDSL.

Inline PoE

Optional internal adapter for inline PoE on 4 switch ports for IP phones or external wireless access points; 802.3af- compliant PoE or 802.3at-compliant PoE+.

External power supply

Product power specifications: C111X Models

AC input voltage: Universal 100 to 240 VAC.

Frequency: 50 to 60 Hz.

Maximum output power: 66W (default).

Output voltages: 12 VDC.

Optional PoE and PoE+:

Single 150W power supply required for Cisco 1100-8P series router

Single 115W power supply required for Cisco 1100-4P series router

External output voltage: 48 VDC.

C1101-4PLTEPWX Models:

AC input voltage: Universal 100 to 240 VAC.

Frequency: 50 to 60 Hz.

Maximum output power: 66W (default).

Output voltages: 12 VDC.

C1101-4P, C1101-4PLTEP, and C1109-2PLTE Models:

AC input voltage: Universal 100 to 240 VAC.

Frequency: 50 to 60 Hz.

Maximum output power: 30W (default iTemp).

Output voltages: 12 VDC.

USB 3.0

USB devices supported:

USB eTokens and USB flash memory

Devices USB 3.0 supports to be connected externally. View the USB Device Support Data Sheet.

LEDs

WWAN (green/amber).

SIM status (green/amber).

Received signal strength indication (RSSI) bar (green).

3G/LTE service (green/amber).

GPS (green/amber).

Speed and link for Gigabit Ethernet WAN port (green).

Speed and link for all Fast Ethernet LAN ports (green).

Physical dimensions (H x W x D)

C111X Models

1.75 x 12.7 x 9.6 in. (44 x 323 x 244 mm) (includes rubber feet on LTE models).

1.75 x 12.7 x 9.03 in. (42 x 323 x 230mm) (includes rubber feet on non-LTE models).

C1101-4PLTEP and C1101-4PLTEPWX Models

1.73 x 9.75 x 6.6 in. (43.9 x 247.6 x 167.6 mm) (includes rubber feet models).

C1101-4P Models

1.1 x 7.5 x 6.0 in. (27.9 x 190.5 x 152.4 mm) (includes rubber feet models).

C1109-2PLTE Models

1.15 x 7.6 x 6.3 in. (29.2 x 193.0 x 160.0mm) (includes rubber feet models).

Pluggable

.85 x 2.5 x 3.88 in. (21.6 x 63.5 x 98.5 mm).

Weight

C111X Models

1.94 lb to 4.59 lb (1.94kg to 2.08 kg).

4.50 lb (2.04 kg) with LTE Advanced.

4.76 lb (2.16 kg) with Wave 2 802.11ac Dual Radio.

4.89 lb (2.22 kg) with LTE Advanced plus Wave 2 802.11ac Dual Radio.

C1101-4PLTEPWX Models

3.34 lb (1.51kg).

C1101-4PLTEP Models

3.78 lb (1.71kg).

C1101-4P Models

1.89 lb (.86kg).

C1102-2PLTE Models

2.25 lb (1.02kg).

Pluggable

EM74XX .44 lb (.20kg).

WP76XX .40 lb (.18kg).

Standard safety certifications

UL 60950-1.and EN 60950-1.

CAN/CSA C22.2 No. 60950-1.

CB to IEC 60950-1, 2nd edition with all group differences and national deviations.

EMC emissions

EN55022/CISPR22, CFR 47 Part 15, ICES003, VCCI-V-3, AS/NZS CISPR22, CNS13438, EN300-386, EN61000-3-2, EN61000-3-3, and EN61000-6-1.

EMC immunity

EN55024/CISPR24, (EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-11), and EN300-386.

Radio immunity

EN301 489-1, EN 301 489-7, and EN301 489-24.

Cellular radio

EN 301 908-1, EN 301 908-2, EN 301 511, 47 CFR Part 22, 47 CFR Part 24, and EN 301 908-13.

Environmental operating range

Nonoperating temperature: -4° to 149°F (-0° to 65°C).

Nonoperating humidity: 5% to 95% relative humidity (noncondensing).

Nonoperating altitude: 0 to 15,000 ft (0 to 4570 m).

Operating temperature: 32° to 104°F (0° to 40°C). C1101 support 32° to 113°F (0° to 45°C). C1109-2PLTE support 32° to 122°F (0° to 50°C).

Operating humidity: 10% to 85% relative humidity (noncondensing).

Operating altitude: 0 to 10,000 ft (0 to 3000 m).