Интерфейсный модуль Cisco SPA-1X10GE-L-V2
Интерфейсные или линейные модули Cisco (linecard, interfacemodule) позволяют расширить маршрутизатор или модульную платформу требуемым функционалом, включая нужные порты доступа на скоростях 1GbE, 10GbE, 40GbE или 100GbE. В основном под каждую серию модульных маршрутизаторов или шасси Cisco выпускает различные модули расширения под определенную линейку устройств, но в большинстве случаев, модуль можно использовать не в одной линейке (напр. интерфейсный модуль Cisco EHWIC-4ESG совместим с маршрутизаторами Cisco ISR G2 1900 серии, 2900 серии и 3900 серии).
В зависимости от платформы, интерфейсный модуль Cisco может поддерживать небольшое количество портов, как в случае с небольшими маршрутизаторами Cisco 1900 серии, так и 48 портов в одном модуле для шасси 7600 серии. Интерфейсные модуля и платы Cisco поддерживают множество различных интерфейсов и могут использоваться как в сети Ethernet, так и в других сетях передачи данных.
Технические характеристики интерфейсного модуля Cisco SPA-1X10GE-L-V2:
|
roduct Compatibility |
• Cisco Catalyst 6500 Series Switches • Cisco 7600 Series Routers • Cisco 12000 Series Routers • Cisco XR 12000 Series Routers • Cisco ASR 1000 Series Router • Cisco CRS Carrier Routing System • Cisco 10000 Series Router |
|
Port Density per SPA |
One 10 Gigabit Ethernet port |
|
Physical Interface |
10-Gbps XFP optics |
|
LED Indicators |
SPA status-Bicolor green and amber LEDs encode the SPA status as follows: • LED off-SPA is powered off • LED amber-SPA is powered on and initializing • LED green-SPA is powered on and operational In addition to the status LED, the SPAs also have a bicolor LED dedicated to each port to indicate port status. The green and amber LEDs encode the port status as follows: • LED off-Port is not activated by software • LED amber-Port is activated by software, but there is a problem with the Ethernet link • LED green-Port is activated by software, and there is a valid Ethernet link |
|
Features and Functions |
• Full-duplex operation • 802.1Q VLAN termination • 802.1ad QinQ termination (stacked VLAN processing) • Jumbo frames support (9188 bytes) • Support for command-line interface (CLI)-controlled online insertion and removal (OIR) • 802.3x flow control • Bridge protocol data unit (BPDU), Cisco Discovery Protocoland VLAN Trunking Protocol (VTP) filtering • Layer 2 Protocol (BPDU, Cisco Discovery Protocol, and VTP) Tunneling • Layer 2 access list (MAC address-based filtering) • Up to 8000 VLANs per SPA and subject to a limit of 4000 VLANs per port for 802.1q • Up to 5000 MAC accounting entries per SPA (source MAC accounting on the ingress, and destination MAC accounting on the egress) • Up to 2000 MAC address entries for destination MAC address filtering per SPA, and up to 1000 MAC address filtering entries per port • Per-port byte and packet counters for policy drops; oversubscription drops; cyclic-redundancy-check (CRC) error drops; packet sizes; and unicast, multicast, and broadcast packets • Per-VLAN byte and packet counters for policy drops; oversubscription drops; and unicast, multicast, and broadcast packets • Per-port byte counters for good bytes and dropped bytes Other software features supported: • Ethernet over Multiprotocol Label Switching (EoMPLS) • QoS • Hot Standby Router Protocol (HSRP) • Virtual Router Redundancy Protocol (VRRP) |
|
Reliability and Availability |
OIR of the SPA within the SIP and the optics within the SPA |
|
Network Management |
Network management: • Field-replaceable XFP modules • Host-system CLI • Simple Network Management Protocol (SNMP) Inventory- and asset management-related MIBs: • Entity-MIB (RFC 2737) • Cisco-entity-asset-MIB Fault management: • Cisco-entity-field-replaceable unit (FRU)-control-MIB • Cisco-entity-alarm-MIB • Cisco-entity-sensor-MIB Physical interface management: • IF-MIB • Etherlike-MIB (RFC 2665) Other MIBs: • Remote Monitoring (RMON)-MIB (RFC 1757) • Cisco-class-based-QoS-MIB • MPLS-related MIBs • Ethernet MIB/RMON |
|
Physical Specifications |
• Weight: 0.75 lb (0.34 kg) • Height: 0.8 in. (2.03 cm) (single height) • Width: 6.75 in. (17.15 cm) • Depth: 7.28 in. (18.49 cm) |
|
Power |
19.9W |
|
Environmental Specifications |
• Storage temperature: -38 to 150°F (-40 to 70°C) • Operating temperature, nominal: 32 to 104°F (0 to 40°C) • Operating temperature, short term: 32 to 131°F (0 to 55°C) • Storage relative humidity: 5 to 95% relative humidity • Operating humidity, nominal: 5 to 85% relative humidity • Operating humidity, short term: 5 to 90% relative humidity • Operating altitude: -60 to 4000 meters |
|
Compliance and Agency Approvals |
Safety • UL 60950-1 • CSA C22 No. 60950-1 • EN 60950-1 • IEC 60950-1 • AS/NZS 60950 • EN 60825-1 • EN 60825-2 • 21 CRF 1040 EMC • CFR 47, FCC Part 15-Class A • ICES 003-Class A • CISPR 22 Class A • EN 55022 Class A • EN 300386 Class A • AS/NZS Class A • VCCI-Class B • EN 50082-1 • EN 55024 • IEC/EN61000-4-2 Electrostatic Discharge Immunity (8-kV contact, 15-kV air) • IEC/EN61000-4-3 Radiated Immunity (10 V/m) • IEC/EN61000-4-4 Electrical Fast Transient Immunity (2-kV power, 1-kV signal) • IEC/EN61000-4-5 Surge AC Port (4-kV CM, 2-kV DM) • IEC/EN61000-4-5 Surge Signal Port (1-kV indoor, 2-kV outdoor) • IEC/EN61000-4-5 Surge DC Port (1 kV) • IEC/EN61000-4-6 Immunity to Conducted Disturbances (10 Vrms) • IEC/EN61000-4-8 Power Frequency Magnetic Field Immunity (30 A/m) • IEC/EN61000-4-11 Voltage Dips, Short Interruptions, and Voltage Variations Telecom • IEEE 802.3ae (10 Gigabit Ethernet interface SPA) Industry Standards The Cisco 1-Port 10-GE SPA is designed to meet the following requirements (some qualifications are currently in progress): • SR-3580-Network Equipment Building Standards (NEBS): Criteria levels (Level 3 compliant) • GR-63-CORE-NEBS: Physical protection • GR-1089-CORE-NEBS EMC and safety |