Точка доступа Aruba (HPE) JY694A

AP-203H SERIES SPECIFICATIONS

· Unified flexible radio 802.11ac 2x2:2SS hospitality and branch AP with internal antennas

· Supports wall-box and desk mount deployments

WI-FI RADIO SPECIFICATIONS

· AP type: Indoor, flexible radio:

· 5GHz 802.11ac 2x2 MIMO OR 2.4GHz 802.11n 2x2 MIMO¹, or

· 5GHz 802.11ac 1x1 AND 2.4GHz 802.11n 1x1¹

· Software-configurable radio supports 5GHz (Radio 0) and/or 2.4GHz (Radio 1)

· 5GHz: Two spatial stream Single User (SU) MIMO for up to 867Mbps wireless data rate to individual 2x2 VHT80 client devices

· 2.4GHz: Two spatial stream Single User (SU) MIMO for up to 400Mbps wireless data rate to individual 2x2 VHT40 client devices (300Mbps for HT40 802.11n client devices)

· Support for up to 32 associated client devices per radio, and up to 8 BSSIDs per radio

· Supported frequency bands (country-specific restrictions apply):

· 2.400 to 2.4835GHz

· 5.150 to 5.250GHz

· 5.250 to 5.350GHz

· 5.470 to 5.725GHz

· 5.725 to 5.850GHz

· Available channels: Dependent on configured regulatory domain

· Dynamic frequency selection (DFS) optimizes the use of available RF spectrum

· Supported radio technologies:

· 802.11b: Direct-sequence spread-spectrum (DSSS)

· 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)

· Supported modulation types:

· 802.11b: BPSK, QPSK, CCK

· 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM

· Transmit power: Configurable in increments of 0.5 dBm

· Maximum (conducted) transmit power (limited by local regulatory requirements):

· 2.4GHz band: +18 dBm per chain, +21 dBm aggregate (2x2 mode)

· 5GHz band: +16 dBm per chain, +19 dBm aggregate (2x2 mode)

· Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain

· Maximum ratio combining (MRC) for improved receiver performance

· Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance

· Short guard interval for 20MHz, 40MHz and 80MHz channels

· Space-time block coding (STBC) for increased range and improved reception

· Low-density parity check (LDPC) for high-efficiency error correction and increased throughput

· Transmit beam-forming (TxBF) for increased signal reliability and range (2x2 mode)

· Supported data rates (Mbps):

· 802.11b: 1, 2, 5.5, 11

· 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54

· 802.11n: 6.5 to 300 (MCS0 to MCS15)

· 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2 for VHT20/40/80)

· 802.11n high-throughput (HT) support: HT 20/40

· 802.11ac very high throughput (VHT) support: VHT 20/40/80

· 802.11n/ac packet aggregation: A-MPDU, A-MSDU

WI-FI ANTENNAS

· Two integrated dual-band moderately directional antennas for 2x2 MIMO with maximum individual antenna gain of 4.9dBi in 2.4GHz and 6.0dBi in 5GHz. Built-in antennas are optimized for vertical orientation of the AP. The horizontal beamwidth is roughly 120 degrees.

· Combining the patterns of each of the antennas of the MIMO radios (in 2x2 mode), the peak gain of the effective per-antenna pattern is 2.3dBi in 2.4GHz and 3.4dBi in 5GHz.

OTHER INTERFACES

· Uplink: 10/100/1000BASE-T Ethernet (RJ-45, back)

· Auto-sensing link speed and MDI/MDX

· 802.3az Energy Efficient Ethernet (EEE)

· PoE-PD (input): 48 Vdc (nominal) 802.3af/at PoE

· Local: 10/100/1000BASE-T Ethernet (RJ-45, bottom)

· Auto-sensing link speed and MDI/MDX

· 802.3az Energy Efficient Ethernet (EEE)

· Passive pass-through interface (two RJ-45, back and bottom)

· USB host interface (Type A connector)

· For Aruba LS-BT1USB BLE radio modules only

· Visual indicators (LEDs):

· Power/system status

· Radio status

· Local network port status

· Reset/LED control button (“paperclip access”)

· Factory reset (when activated during device power up)

· LED control: toggle off/normal

· Serial console interface (custom, uUSB physical jack)

ENCRYPTED THROUGHPUT

· Maximum IPsec encrypted wired throughput: 20Mbps

POWER SOURCES AND CONSUMPTION

· The AP is powered through Power over Ethernet (PoE)

· An optional PoE power injector is sold separately

· Power over Ethernet (PoE): 48 Vdc (nominal) 802.3af/802.3at compliant source

· Maximum (worst-case) power consumption: 7.4W.

· Includes up to 100mW for an attached USB BLE module

· Maximum (worst-case) power consumption in idle mode: 3.9W.

MOUNTING

· The AP ships with a mounting plate to attach the AP to a single-gang wall-box (most international variations covered). The AP securely attaches to the plate; a custom security tool to remove the AP from the plate ships with the product.

· Several optional mount kits are available to attach the AP to a dual-gang wall-box, directly to the wall, or to support desk mounting.

MECHANICAL

· Dimensions/weight (unit,including single-gang wall box mount plate):

· 86mm (W) x 26.5mm (D) x 140mm (H)

· 225g

· Dimensions/weight (shipping):

· 115mm (W) x 47mm (D) x 165mm (H)

· 290g

ENVIRONMENTAL

· Operating:

· Temperature: 0° C to +40° C (+32° F to +104° F)

· Humidity: 5% to 93% non-condensing

· Storage and transportation:

· Temperature: -40° C to +70° C (-40° F to +158° F)

REGULATORY

· FCC/Industry of Canada

· CE Marked

· R&TTE Directive 1995/5/EC

· Low Voltage Directive 72/23/EEC

· EN 300 328

· EN 301 489

· EN 301 893

· UL/IEC/EN 60950

· EN 60601-1-1 and EN 60601-1-2

For more country-specific regulatory information and approvals, please see your Aruba representative.

RELIABILITY

· MTBF: 780,000 hours (89 years) at +25C° operating temperature

REGULATORY MODEL NUMBER

· AP-203H-xx (all variants): APINH203

CERTIFICATIONS

· CB Scheme Safety, cTUVus

· UL2043 plenum rating

· Wi-Fi Alliance (WFA) certified 802.11a/b/g/n/ac