Точки доступа Aruba (HPE) обеспечивают быструю и стабильную беспроводную передачу данных в корпоративной сети. Aruba предлагает как простые устройства для предоставления базового функционала сети Wi-Fi, так и для сетей с высокой плотностью пользователей и скоростями до 2 Гбит/с, а также защищенные модели для работы в сложных климатических условиях.
Точки доступа просты в инсталляции, могут работать одновременно в диапазонах 2,4 и 5 ГГц, используют технологию MIMO для увеличения скорости передачи данных и поддерживают стандарт 802.11ac Wave2.
Instant-точки доступа Aruba — не требуют отдельного контроллера, а используют виртуальный контроллер, функции которого выполняет одна из точек. HPE Aruba Instant — это решение, которое позволяет развернуть «бесконтроллерную» сеть WiFi корпоративного уровня. В него уже встроена сетевая безопасность, автоматическое управление RF и достаточно интеллектуальных функций для запуска полноценного решения без дополнительного лицензирования. Управляется кластер из точек доступа при помощи виртуального контроллера, который размещается на одной из точек доступа (IAP). Контроллер отвечает за процесс автоконфигурирования новых точек доступа, авторизацию и аутентификацию, гостевой доступ и сетевые сервисы (NAT, DHCP и др.).
Технические характеристики точки доступа Aruba (HPE) JY720A:
|
RAP-203R SERIES SPECIFICATIONS
|
- Unified flexible radio 802.11ac remote AP with internal antennas.
- Supports wall-box and desk mount deployments
|
|
WI-FI RADIO SPECIFICATIONS
|
- AP type: Indoor, flex radio:Software-configurable radio supports 5GHz (Radio 0) and/or 2.4GHz (Radio 1)
- 5GHz 802.11ac 2x2 MIMO OR 2.4GHz 802.11n 2x2 MIMO1, or
- 5GHz 802.11ac 1x1 AND 2.4GHz 802.11n 1x11
- 5GHz: Two spatial stream Single User (SU) MIMO for up to 867Mbps wireless data rate to individual 2x2 VHT80 client devices
- 2.4GHz: Two spatial stream Single User (SU) MIMO for up to 400Mbps wireless data rate to individual 2x2 VHT40 client devices (300Mbps for HT40 802.11n client devices)
- Support for up to 256 associated client devices per radio, and up to 16 BSSIDs per radio
- Supported frequency bands (country-specific restrictions apply):Available channels: Dependent on configured regulatory domain
- 2.400 to 2.4835GHz
- 5.150 to 5.250GHz
- 5.250 to 5.350GHz
- 5.470 to 5.725GHz
- 5.725 to 5.850GHz
- Dynamic frequency selection (DFS) optimizes the use of available RF spectrum
- Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
- Supported modulation types:Transmit power: Configurable in increments of 0.5 dBm
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
- Maximum (conducted) transmit power (limited by local regulatory requirements):Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks
- 2.4GHz band: +18 dBm per chain, +21 dBm aggregate (2x2 mode)
- 5GHz band: +18 dBm per chain, +21 dBm aggregate (2x2 mode)
- Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain
- Maximum ratio combining (MRC) for improved receiver performance
- Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
- Short guard interval for 20MHz, 40MHz and 80MHz channels
- Space-time block coding (STBC) for increased range and improved reception
- Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
- Transmit beam-forming (TxBF) for increased signal reliability and range
- Supported data rates (Mbps):802.11n high-throughput (HT) support: HT 20/40
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 300 (MCS0 to MCS15)
- 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2 for VHT20/40/80)
- 802.11ac very high throughput (VHT) support: VHT 20/40/80
- 802.11n/ac packet aggregation: A-MPDU, A-MSDU
|
|
WI-FI ANTENNAS
|
- Two integrated dual-band omni-directional antennas for 2x2 MIMO with maximum individual antenna gain of 0.7dBi in 2.4GHz and 1.0dBi in 5GHz. Built-in antennas are optimized for vertical orientation of the AP.
- Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the effective per-antenna pattern is -0.4dBi in 2.4GHz and 0.5dBi in 5GHz.
|
|
OTHER INTERFACES
|
- Uplink: 10/100/1000BASE-T Ethernet (RJ-45, back)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Efficient Ethernet (EEE)
- Local: Two 10/100/1000BASE-T Ethernet (RJ-45, back)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Efficient Ethernet (EEE)
- One port (E2): PoE-PSE (output): 48 Vdc (nominal) 802.3af PoE (AP-203RP models)
- Bluetooth Low Energy (BLE) radio
- Up to 4dBm transmit power (class 2) and -93dBm receive sensitivity
- Integrated antenna with moderately directional pattern and peak gain of 1dBi
- USB 2.0 host interface (Type A connector, top)AC power interface, 2 prong IEC 60320-1 C8 receptacle (back)
- 3G/4G cellular modems
- Device battery charging port
- Capable of supplying up to 1A/5 watts of power to an attached device
- Visual indicators (LEDs, front):
- Power/system status
- Radio status
- Local network port status (2x)
- Includes PoE-PSE status (AP-203RP models)
- Reset/LED control button (“paperclip access”, bottom)Serial console interface (custom, uUSB physical jack, bottom)
- Factory reset (when activated during device power up)
- LED control: toggle off/normal
|
1 256-QAM modulation (802.11ac) supported by the 2.4GHz radio as well.
|
ENCRYPTED THROUGHPUT
|
- Maximum IPsec encrypted wired throughput: 20Mbps
|
|
POWER SOURCES AND CONSUMPTION
|
- The AP supports direct AC power: 90V – 265V, 47Hz – 63Hz.
- Note that the unit does not include an AC power cord (IEC C7 plug). A compatible region-specific cord should be selected and added when ordering the AP.
- Maximum (worst-case) power consumption: 7.5W.Maximum (worst-case) power consumption in idle mode: 4.6W.
- Excludes power consumed by external USB and/or PoE-PD device (and internal losses); this could add up to 6W for a 5W/1A USB device and up to 18W for a max load (15.4W) 802.3af PoE-PD device
|
|
MOUNTING
|
- The AP supports desk mount without additional accessories. A cover ships with the AP to hide connectors, cables and product labels.
- The cover can be used to support wall mounted deployments as well.
|
|
MECHANICAL
|
- Dimensions/weight (unit, with cable cover):
- 155mm (W) x 50mm (D) x 95mm (H)
- 320g (AP-203R), 340g (AP-203RP)
- Dimensions/weight (shipping):
- 224mm (W) x 159mm (D) x 78mm (H)
- 510g (AP-203R), 590g (AP-203RP)
|
|
ENVIRONMENTAL
|
- Operating:
- Temperature: 0° C to +40° C (+32° F to +104° F)
- Humidity: 5% to 93% non-condensing
- Storage and transportation:
- Temperature: -40° C to +70° C (-40° F to +158° F)
|
|
REGULATORY
|
- FCC/Industry of Canada
- CE Marked
- R&TTE Directive 1995/5/EC
- Low Voltage Directive 72/23/EEC
- EN 300 328
- EN 301 489
- EN 301 893
- UL/IEC/EN 60950
- EN 60601-1-1 and EN 60601-1-2
For more country-specific regulatory information and approvals, please see your Aruba representative.
|
|
RELIABILITY
|
- MTBF at +25C° operating temperature:
- AP-203R: 324,000 hours (37 years)
- AP-203RP: 308,000 hours (35 years)
|
|
REGULATORY MODEL NUMBER
|
- AP-203R-xx (all variants): APINR203
- AP-203RP-xx (all variants): APINP203
|
|
CERTIFICATIONS
|
- CB Scheme Safety, cTUVus
- Wi-Fi Alliance (WFA) certified 802.11a/b/g/n/ac
|
|
WARRANTY
|
|
Aruba limited lifetime warranty
|
|
MINIMUM SOFTWARE VERSION
|
- ArubaOS™ 6.5.2.0/8.2.0.0
- Aruba InstantOS™ 6.5.2.0/8.2.0.0
|
